Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Duct Sealing in Los Angeles: What to Know First
Abatement Technologies duct sealing in Los Angeles runs $450 to $1,600 depending on how much of the system has separated at the joints and whether the ductwork is accessible from an attic, crawl space, or slab. Most Abatement Technologies jobs take one visit, usually four to six hours, and we price the work in writing before anyone opens a toolbox. We’re an independent Abatement Technologies service provider – not a factory warranty center – which means we can use the best parts for the job, not just the most expensive ones.
If you own a home in Los Angeles with Abatement Technologies filtration or ducting installed and you’re feeling weak airflow at far registers, seeing dust return days after cleaning, or paying for cooled air that never reaches the bedroom at the end of the hall, this page covers what’s going on and what it costs to fix. Call (361) 326-5060 and you’ll get a person, not a menu tree.
How Abatement Technologies Products Fail – and How We Fix Them
Abatement Technologies builds serious commercial-grade air handling and filtration equipment, and a lot of it has made its way into Los Angeles condo buildings, medical suites, and high-end residential retrofits. But the ductwork that carries the air is only as tight as its weakest seam. Here’s what we find when those seams fail.
- Halo duct collar separation at the plenum. On Abatement Technologies Halo fan filter units and integrated blower cabinets, the takeoff collars are often attached with a thin bead of factory mastic. After a few Los Angeles summers with the system cycling between 72 at night and 95 at 4 p.m., that bead cracks like old caulk. The symptom is a faint whistling near the unit and airflow that drops off past the first register. Our fix: re-seat the takeoff, clean the metal to bright, apply duct mastic to the full lap joint, and screw the collar every four inches before sealing the screws. That joint should outlast the equipment.
- Flex runs pulling loose from Abatement Technologies air distribution boxes. The plenum boxes Abatement Technologies specs on larger L.A. retrofit jobs use round outlets that rely on plastic flanges and a zip-tie cinch. Plastic fatigues. When the flange deforms from heat, the flex duct sags and creates a hidden leak inside the wall or attic. We see warm attics in the San Fernando Valley turning this into a two- or three-year failure cycle. Our fix: swap the plastic flange for a metal collar with a rolled bead, pull the flex tight, and cinch with two bands, not one. Then we test static pressure to confirm the run is actually carrying air.
- Access-door gaskets failing on Abatement Technologies MODULAR or custom filter housings. Not a duct seam, but the same air-loss problem: the neoprene gasket on a filter access door compresses permanently after a few changeouts, and now your blower is sucking unfiltered air from a mechanical closet instead of through the returns. The dust level in your home climbs. Our fix: replace the gasket, adjust the door latch tension, and run a smoke pencil along the door seal with the blower on to prove it’s tight.
- Return-side cavities opened by remodelers in older Los Angeles homes. Abatement Technologies equipment gets installed in a lot of 1980s and 1990s L.A. houses where the return chase is drywall pocketed between joists. When a contractor pulls permits and opens a wall, they don’t always button the chase back up. Now the system is pulling air from the stud cavity, the garage, or behind the bath. Dirty, unconditioned air. Our fix: inspect the full return path with a borescope where accessible, seal every breach with closed-cell foam or metal and mastic, and verify the return-side negative pressure returns to spec.
- Ductboard ends delaminating on Abatement Technologies-specified rigid runs in commercial conversions. Some Abatement Technologies projects in Los Angeles converted warehouse or retail space use fiberglass ductboard. The facing peels at the cut edges over time, and once moist air cycles through, the board itself starts shedding. This one is usually beyond sealing – it’s re-lining or replacement. We’ll give you an honest read before recommending a repair that would only buy two years.
Our Abatement Technologies Duct Sealing Process
Every Abatement Technologies duct sealing job in Los Angeles follows the same path. It keeps the price honest and leaves no room for surprises.
- 1
Call and schedule. You talk to a live person at (361) 326-5060, we book a two-hour window, and the technician arrives inside that window, uniformed and driving a marked van.
- 2
Diagnostics first. We walk the system, look at the returns, check airflow at three or four registers, and note where the pressure seems wrong. For Abatement Technologies equipment, we spend extra time on collars, flanges, access gaskets, and the return-side chase. You hear what we find in plain language.
- 3
Written price, no moving target. The number is on paper before any work starts. One flat price per system, parts and labor included. If we find something mid-repair that changes the scope, we show you before we touch it.
- 4
The work. We use mastic, UL-listed tapes, and metal collars where needed. If the Abatement Technologies unit has an OEM part that’s still under its manufacturer warranty, we can coordinate the warranty placement; if the warranty’s done, we’ll tell you when a quality aftermarket part does the same job for less. No downsells, either – if the part matters, we say so.
- 5
Test and show. After sealing, we check static pressure and airflow at the previously weak registers. You get before-and-after readings, plus photos of the sealed joints you couldn’t see if you tried.
- 6
The 365-Day Done Right Promise, in writing. If the repair fails within a year, we come back at no charge – including a free second visit. That’s the whole point of doing it right the first time.
What Abatement Technologies Duct Sealing Costs in Los Angeles
Here’s what we charge for the most common Abatement Technologies duct sealing jobs. These are real figures for the Los Angeles market – not teaser numbers that double at the door.
| Job | Typical Price |
|---|---|
| One or two collar/plenum joint failures near the unit | $450 – $650 |
| Multiple flex-run leaks, attic or crawl accessible | $800 – $1,200 |
| Return-chase sealing across a multi-zone Abatement Technologies system | $900 – $1,600 |
| Access-door / filter-housing gasket replacement and reseal | $300 – $500 |
| Full-system duct sealing after a remodel, three to six zones | $1,200 – $2,200 |
What moves the price: accessibility of the ductwork, number of leaking joints, how much of the run has to be reached from a tight attic, and whether any sections are too far gone to seal. Homes in the Hills, in the Valley, and across the basin all have different attic conditions – pricing follows what the structure actually requires. Call (361) 326-5060 and we’ll give you a written estimate for your specific system. Estimates are free.
Why Los Angeles Homeowners Call Hollis Air Duct Cleaning for Abatement Technologies Work
Hollis Air Duct Cleaning is an independent business under the Garrison Partners family, and we’ve been in operation since 2004. Roy Castellanos runs our crew, and he’s been doing hands-on duct work in Los Angeles County since before a lot of our competitors had a truck. What that buys you: a technician who has actually opened up Abatement Technologies equipment in L.A. attics and knows what the heat, dust, and remodel history of this city do to a duct system.
Every job carries the 365-Day Done Right Promise, in writing. If the repair fails inside a year, we return and make it right at no cost – including the second visit. You get written pricing before work starts, not after. We work on more than one brand, so when we’re in your mechanical room, we’re solving the problem, not chasing a commission on an Abatement Technologies part number. If we spot a Lennox, Trane, or Carrier issue while we’re in there, we’ll tell you straight.
FAQs
Yes. As an independent Abatement Technologies service provider, we perform duct sealing without touching the internal components of the unit itself, so the manufacturer’s warranty on the equipment is unaffected. What we seal is the duct network connected to the Abatement Technologies system, which is field-installed and not a warrantied part for most residential applications. If a failure inside the unit is covered, we’ll point you to the warranty process instead of selling you an unnecessary repair.
We provide before-and-after static pressure readings and airflow measurements at the registers that were previously weak, and we photograph every joint we seal. You’ll see what we found, what we did, and the numbers that show the difference. If a far register is still weak after the repair, the 365-Day Done Right Promise means we come back without charge. For a direct answer on your system, call (361) 326-5060.
Because they’re usually scoped wrong – a collar seal quoted as a five-minute job, or flex leak repairs priced without allowance for the real labor of getting into a hot L.A. attic and doing the work properly. Or the price is a teaser that changes when the tech arrives. Our prices are written before work starts, and the number does not move. A lower number on the phone doesn’t mean a lower invoice later.
Done right, it should not need to be redone. The materials we use – mastic, UL-listed tapes, metal collars – are life-of-system when applied to a clean surface. What fails again is the same thing that failed the first time: plastic flanges, thin factory mastic, and flex runs with one loose cinch. We fix those to a standard that’s meant to last, which is why we back it for a full year. Call (361) 326-5060 for a system-specific assessment.
Yes, though the pricing reflects the harder access. Hillside homes often have ductwork running through tight sloped attics, cramped crawl spaces, or narrow chases, and that’s where the good work is slower. We’ve sealed systems in those conditions across Los Angeles, and we’ll give you a written price for what the structure actually demands before we start. Free estimate – call (361) 326-5060 to book.
Written by Roy Castellanos, Owner, Hollis Air Duct Cleaning at Hollis Air Duct Cleaning, serving Los Angeles and nearby areas.